+91 8813083500

Category: Arduino

Learn Robotics

Arduino Solar Powered Pong Game

ABOUT THIS PROJECT In this Arduino Game Project we are going to build an Arduino Game, the clasic Pong game! It is a very easy Arduino Project to build, it won’t take you more than 15 minutes! And we can charge it using a solar panel which is stick on its back side. It uses…
Read more

DIY Cheap & Portable Power Supply Version 1.0

DIY Cheap & Portable Power Supply Version 1.0 There are a lots of power supplies in market but those are too expensive for a Arduino Beginner or a Hobbyist. So I decided to make a Good Looking and Cheap power supply out of cheap modules. the power Supply must be handy as well as Powerful.…
Read more

Ambient Real Time Clock

9+COMPONENTS AND SUPPLIES Arduino Nano R3 × 1 Real Time Clock (RTC) × 1 Linear Regulator (7805) × 1 SparkFun LilyPad Rainbow LED (strip of 7 colors) × 1 NECESSARY TOOLS AND MACHINES Soldering iron (generic) APPS AND ONLINE SERVICES Arduino IDE ABOUT THIS PROJECT Ambient Lightning Real-Time Clock Aim I made this Clock because…
Read more

How to use a Colored OLED Display SSD1331

How to drive the Arduino color OLED The display is very small. It has almost the same size as the monochrome OLED display. But the resolution of it is not the same. It has a resolution of 96×64 pixels. So, it has a lower resolution at the same size. It can display 65 thousand colors! The display…
Read more

Led Matrix DIY for Arduino Nano

Dot Matrix 8×8 Make a cheap and good looking LED matrix Things used in this project Hardware components Arduino Nano R3 × 1 LED (generic) × 1 OSH Park Custom fabricated PCB × 1 Software apps and online services Arduino IDE Hand tools and fabrication machines Soldering iron (generic) Story Theory of LED dot matrix…
Read more

Arduino Quadcopter

By PrashantS161Follow Its not only a Quadcopter ,,,, Its a open source Machine!!!! Many of you face a problem when it comes to Flight Controller which is the brain of the Multirotor. There are plenty of ready-made pre-flashed Flight controllers in the market for cheap, But have you thought of building your own Flight controller with…
Read more

Arduino Spirit Level with LCD

Parts list: Arduino board LCD 16×2 Gyroscope MPU-6050 Potentiometer 10K Resistor 220 ohm Breadbord Connecting wire Wiring: Video: Code: #include <LiquidCrystal.h> LiquidCrystal lcd(7, 8, 9, 10, 11, 12); #include <Wire.h> //Declaring some global variables int gyro_x, gyro_y, gyro_z; long acc_x, acc_y, acc_z, acc_total_vector; int temperature; long gyro_x_cal, gyro_y_cal, gyro_z_cal; long loop_timer; int lcd_loop_counter; float angle_pitch,…
Read more

Line Follower Robot Arduino 

Line Follower Robot Arduino Line Follower Robot follows a black line. arduino project infrared ir sensor line follower COMPONENTS AND SUPPLIES Arduino UNO & Genuino UNO × 1 SparkFun Dual H-Bridge motor drivers L298 × 1 Proximity Sensor × 1 APPS AND ONLINE SERVICES Arduino IDE ABOUT THIS PROJECT Line Follower Robot Best & Fast…
Read more

How to Make Radio Controlled Arduino Car with FS-iA6 and Motor Driver Board

Radio Controlled Arduino Car with FS-iA6 and Motor Driver Board In this article i will guide you in detail how to Make Radio Controlled Arduino Car with FS-iA6 and LM298N Motor Driver Board so that you can make one of your own. This Arduino Project is easy to make and Fun to play with therefore…
Read more

Open Pilot GCS

OpenPilot You can use the OpenPilot Ground Control Station (GCS) both to configure your controller board and to control and monitor your aircraft during flight. More commonly, you would use a conventional radio control transmitter to control your vehicle, but the GCS is also capable of doing so.   All OpenPilot products use the same…
Read more